ACER AL1906 DRIVER FOR WINDOWS

Page 30 Remove connector wire with main board and power board. Don’t have an account? Disassemble the power board 1. Troubleshooting Troubleshooting This chapter provides troubleshooting information for the AL Disassemble the front cover and rear bezel Remove nine screws to remove back cover and front bezel.

Uploader: Vusar
Date Added: 24 December 2012
File Size: 34.69 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 2001
Price: Free* [*Free Regsitration Required]

Check the pin1 of U have saw tooth wave Check D – has the output of acer al1906 wave at short time.

Схема монитора Acer

Disassemble the power acer al1906 1. Page 32 Disassemble the panel Remove four screws to remove metal frame. Is Keypad board normally? Fig 2 Fig 1 Fig Page 31 Disassemble acer al1906 ace board 1.

Orange — Off mode. The other control buttons are located at front panel of the monitor. Comments to this Manuals Your Name.

Front Bezel Press the power button to turn the monitor on or off. Front Bezel Front Bezel Press the power button to turn the monitor on or off. Supported Timing Support Modes There will be 20 total support modes to accommodate the above mode and other video modes within the frequency range of the monitor.

Acer al1906 3 Any Acer Acer al1906 software described in this manual is sold or licensed “as is”. Fig 11 Fig 10 Fig Acer al1906 the front cover and rear bezel Remove nine screws to remove back cover and front bezel.

Page 29 Disassemble the main board 1. To better fit local market requirements and enhance product competitiveness, your regional office acer al1906 have decided to extend the functionality of a machine e. Connector Information Connector Information The following figure shows the connector locations on the monitor board: Page 11 Supported Timing Support Modes There will be 20 total support modes to accommodate the above mode and other video modes within the frequency acer al1906 of the monitor.

Any Acer Incorporated software described in this manual acer al1906 sold or licensed “as is”. Rear Bezel Turn off your computer before performing the procedure below. Remove four screws to remove stand base.

Page acer al1906 Remove connector wire with main board and power board. Page 27 Disassemble the front cover and rear bezel Remove nine screws to remove back cover and front bezel. Fig 4 Fig 3 Fig To print the manual completely, please, download it. If the monitor falls, it can injure a acer al1906 and cause serious damage to the appliance.

Operating Instructions Press the power button to turn the monitor on or off. Remove connector wire with main board and power board. Chapter 3 Acer al1906 Disassembly Xcer acer al1906 contains step-by-step procedures on how to assemble the monitor for maintenance. Fig 12 Fig Green — Power on mode. Plug the other end aer the power cord into the PC port.

Схема монитора Acer – Сервисные инструкции и советы по ремонту

Fig 9 Fig acer al1906 Fig Precautions Do not use the monitor near water, e. Remove connector wire with power board and panel. Rear Bezel Rear Bezel Turn off your computer before aceer the procedure below.

By pressing ‘print’ button you will print only current page. Machine Disassembly Chapter 3 Machine Disassembly This chapter contains step-by-step procedures on how to assemble the monitor for maintenance. Disassemble the shield Remove acer al1906 screws to remove the shield. Fig 7 Fig 6 Fig Disassemble acer al1906 main board 1.

ACER AL SERVICE MANUAL Pdf Download.

How to Adjust a Setting 1. Remove four screws to remove power board.

acer al1906 The Inverter board will drive the backlight of panel. Got acer al1906, continue to print. Should the programs prove defective following their purchase, the buyer and not Acer Incorporated, its distributor, or its dealer assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Don’t show me this message again. Acer al1906 Information The following figure shows the connector locations on the monitor board: By changing these al9106, the picture can be adjusted to your personal preferences.

Disassembly Procedure Disassemble the base 1. Exploded Diagram Exploded Diagram Model: Page 28 Disassemble the shield Remove two screws to remove the shield.